SOLIDWORKS PDM Archives

shahmeer

shahmeer
October 4, 2025
No Comments

Extension Specific Export Location

Each extension can be exported to a specified location

shahmeer

Amen Jlili

Amen Jlili
October 4, 2025
No Comments

Add Bookmarks To Exported PDFs

AND/OR Conditions control references are processed.

Amen Jlili

Table of Content In Merged PDF and Screenshot of a simple Bill of Materials (BOM) table generated by PDMPublisher (SOLIDWORKS) version 20250906. The header reads: "Job ID a1a85a78-10a5-415f-9ced-383ae9d6c186 - Document: Full_Grill_Assembly.SLDASM - [VER: PDMPublisher (SOLIDWORKS) V20250906]" The table has four columns: Name, PartNumber, Status, Qty. Rows: Full Grill Assembly | 108153 | (blank) | 1 Support Frame End & | 108149 | (blank) | 2 side_table_shelf_&_burner & | 108150 | (blank) | 1 side_table_shelf_for_burner & | 108161 | (blank) | 1 side_table_plank_wood & | 108163 | (blank) | 7 The image shows an automatically exported BOM listing the top-level components and quantities for the "Full Grill Assembly" assembly.

Amen Jlili

Amen Jlili
October 4, 2025
No Comments

Table of Content In Merged PDF

Add a Table Of Content to the merged PDFs

Amen Jlili

Add A Watermark To Your PDFs and Screenshot of SOLIDWORKS 2025 with the PDMPublisher (SOLIDWORKS) add-in open. The main drawing area is mostly empty and beige, displaying a small projected view of a colourful 3D speaker component (orange cone, purple surround, and grey frame) in the top-left corner. Centered in the drawing is a large semi-transparent white banner with bold black text reading PREVIEW ONLY and a small red close button. At-branded watermark "Amen Billi" appears near the speaker view. The top command bar shows the PDMPublisher tab active with sub-tabs Annotations, Conditions, Logs, and About. The title bar at the top right reads "speaker - Sheet1". The status bar at the bottom indicates "Editing Sheet1" and "Under Defined". The interface shows the PDMPublisher add-in in preview mode, preventing editing until the document is formally published.

Amen Jlili

Amen Jlili
October 4, 2025
No Comments

Add A Watermark To Your PDFs

Add a watermark to your export PDFs

Amen Jlili

Conditional Assembly Processing and Screenshot of SOLIDWORKS 2025 showing a part modelling environment with the PDMPublisher (SOLIDWORKS) add-in open. On the left, the FeatureManager tree displays a simple cylindrical part (a tank or bottle-like shape) built with features such as Base-Revolve, Fillet, Boss-Extrude, and Upper Casing. The 3D model is rendered in shaded-with-edges style and viewed isometrically. On the right, the PDMPublisher pane is active on the "Conditions" tab. A single condition rule is defined under a group set to AND: the variable "Workflow" must have text equal to "Released" (shown with a green checkmark), while the Configuration Name column has a red X indicating no condition is applied. Buttons for Export, Import, and Help are visible at the top, and a large "PUBLISH" button sits at the bottom. The interface demonstrates configuring the PDMPublisher add-in to publish only parts that have reached the "Released" workflow state.

Amen Jlili

Amen Jlili
October 4, 2025
No Comments

Conditional Assembly Processing

AND/OR Conditions control references are processed.

Amen Jlili

SOLIDWORKS Part Documents and Screenshot of the SOLIDWORKS “Add-Ins” dialog box. The window shows three sections: “SOLIDWORKS Professional Add-ins” (empty), “SOLIDWORKS Add-ins” (empty), and “Other Add-ins”. Under “Other Add-ins”, the only listed item is “PDMPublisher (SOLIDWORKS)”, which is checked in both the “Start Up” and active-session columns (shown with a blue checkmark) and is highlighted with a red border. Buttons at the bottom are “OK” (highlighted in blue) and “Cancel”. This confirms that the third-party PDMPublisher add-in is currently enabled and set to load automatically every time SOLIDWORKS starts.

Amen Jlili

Amen Jlili
October 4, 2025
No Comments

SOLIDWORKS Part Documents

Publish STEP, IGES, X_T, EPRT, HTML from parts.

Amen Jlili

Amen Jlili

Amen Jlili
October 4, 2025
No Comments

Merge Multiple Drawings Into One PDF

Combine multiple PDFs into one final document.

Amen Jlili

$SOLIDWORKS Drawing Documents and Screenshot of SOLIDWORKS 2025 Professional showing a detailed 2D engineering drawing (Sheet1) of a curved metal bracket or tank support with multiple dimensions (e.g., 50.80, 12.70, 457.20, 378.46, 6.35, 25.40, 175°). The drawing includes centre lines, radius callouts, and a rounded rectangular cutout. The PDMPublisher (SOLIDWORKS) pane is open on the right on the Output tab. A blue banner at the top reads “A new version is out. Click here to download it”. Export settings show: Export Location “C:\speaker project”, Filename template “File name without extension” + “Revision” (both parts marked with red X indicating invalid), File Formats set to “pdf”, and “Open Export Location On Completion” checked. Other export options are unchecked. A large “PUBLISH” button is visible at the bottom. The image captures a drawing editing mode with the PDMPublisher add-in ready (but currently blocked by the invalid filename template) to export the drawing as PDF.$

Amen Jlili